Hey,
Im looking at getting some 19s for my ride. have found some pretty nice rims, but the thing is can i fit 19*9.5 on the magna?

Tried searching but couldnt see....
thanks for any help

you could just fit that on the back.... one person's done it before (cummins)
but i doubt you'd fit them on the front. you could try putting 18's on the front, and having the 19's on the rear like booya, but it just depends what u like the look of.

ive got 18x7.5 and my fronts are out by 2mm i was told when they were installed.

you could try putting 18's on the front, and having the 19's on the rear like booya, but it just depends what u like the look of.

booya has 19s all round, dunno where you got that info from

you can go 19x9.5 rear and 19x8 front... why not just go 19x8 all round though, do you really need it 9.5 wide?

booya has 19s all round, dunno where you got that info from

you can go 19x9.5 rear and 19x8 front... why not just go 19x9 all round though, do you really need it 9.5 wide?

Booya had plans for 18's on the fronts so he could have Semi Slicks.

Booya had plans for 18's on the fronts so he could have Semi Slicks.

ah i see, nice!

go 19x8 all round. having wider tires on the back might accentuate understeer.

did u forget u drive a front wheel drive car? why do u need wider rubber on the back?

you can go 19x9.5 rear and 19x8 front...

no. you can go 8.5 wide all around, just need to cut a little bit off the inside of the front arches. but it really depends on your offset. if you have too much offset, then you'll be lucky to fit 7"

booya has 19s all round, dunno where you got that info from

you can go 19x9.5 rear and 19x8 front... why not just go 19x8 all round though, do you really need it 9.5 wide?

I would go 19*8 all round if i could, but these specific rims are said to be 19*9.5 and thats why i asked in the first place...

I don't know about where you are, but in NSW 1" over stock width is all you can go, which normally means 7" max. Kinda limits your options if you want to stay legal...

hell i'd be stuffed trying to put 19's on mine, the 16x6.6 ive got on it stick out on the front, and scape on the plastic inner gaurds on U turns

I don't know about where you are, but in NSW 1" over stock width is all you can go, which normally means 7" max. Kinda limits your options if you want to stay legal...

Im in NSW, and legal isnt a problem....
can always get it engineered or find someone to write off defects

hell i'd be stuffed trying to put 19's on mine, the 16x6.6 ive got on it stick out on the front, and scape on the plastic inner gaurds on U turns

I got 17*7 at the moment and theres plenty of room.
19*8 would go fine i recon. we'll see....

19*8 would go fine i recon. we'll see....

19 x 8 will fit, depending on your offset..... hell 9.5" should fit, if you get the correct offset, and the correct wheel.

Put a set of 19 x 8.5's on the VRX and they fit fine, just put of set of King springs in and sits fine.

Pic's here (Before lowering)

Im in NSW, and legal isnt a problem....
can always get it engineered or find someone to write off defects
Sorry to hijack the thread slightly, but what's the ruling with that? "Anything goes if you can get it engineered" ? Any idea what that would cost?

in WA your not leagally alloud to go bigger than 2inchs of what the standard rim is