s_tim_ulate
30-07-2005, 02:30 PM
Well as has been on the agenda for quite some time, I've been looking to replace my previously crappy Cadence tweeters that i was using as ambient tweets to complement the morels and give a bit more stage height.
I ended up going all out and getting a a set of Dynaudio MD100's. As featured in the 2 and 3 way Dynaudio setups.
Few specs
Thiele Small Parameters Magnet and Voice Coil Properties
Nominal impedance Znom 4 Ω Voice coil diameter dc 28 mm
DC resistance Re 3.2 Ω Voice coil height hc 1.7 mm
Voice coil inductance Le 0.014 mH Voice coil layers nc 2
Resonance frequency fs 1360 Hz Magnetic gap height hg 2 mm
Mechanical Q factor Qms 1.0 Linear excursion, peak to peak - mm
Electrical Q factor Qes 2.2 Max. excursion, peak to peak - mm
Total Q factor Qts 0.7 Magnet weight wm 0.02 kg
Mechanical resistance Rms - kg/s
Moving mass (incl. air load) Mms 0.35 g Power Handling
Suspension compliance Cms - mm/N Nominal long term IEC* 100 W
Effective dome diameter d 31.3 mm Transient (10 ms) 500 W
Effective piston area Sd 7.7 cm2
Equivalent volume Vas -1 Mechanical Properties
Force factor Bl 2 Tm Net weight 0.126 kg
Recommended frequency range 2500-30000Hz Overall dimension ø62.2x43 mm
* Depending on crossover
First off take notice of the size of these babies... They are massive! (28mm) And very heavy as well.
I quickly knocked up a bracket for them last night (mounted in the kicks again) and wired them up. They extend down very low for tweets - with a fs of 1360 hz.
Also handle all the power I have to give them with great detail and warmth.
I've moved the Morels up to ambients, which was a bit of a struggle getting them to fit in the same holders, but after a bit of modding got them in.
Absolutely love these Dyn's. Cant recommend Dynaudio and Morel more highly.
Still require a lot of tweaking, but for now Im a happy man.
Peace
Tim
I ended up going all out and getting a a set of Dynaudio MD100's. As featured in the 2 and 3 way Dynaudio setups.
Few specs
Thiele Small Parameters Magnet and Voice Coil Properties
Nominal impedance Znom 4 Ω Voice coil diameter dc 28 mm
DC resistance Re 3.2 Ω Voice coil height hc 1.7 mm
Voice coil inductance Le 0.014 mH Voice coil layers nc 2
Resonance frequency fs 1360 Hz Magnetic gap height hg 2 mm
Mechanical Q factor Qms 1.0 Linear excursion, peak to peak - mm
Electrical Q factor Qes 2.2 Max. excursion, peak to peak - mm
Total Q factor Qts 0.7 Magnet weight wm 0.02 kg
Mechanical resistance Rms - kg/s
Moving mass (incl. air load) Mms 0.35 g Power Handling
Suspension compliance Cms - mm/N Nominal long term IEC* 100 W
Effective dome diameter d 31.3 mm Transient (10 ms) 500 W
Effective piston area Sd 7.7 cm2
Equivalent volume Vas -1 Mechanical Properties
Force factor Bl 2 Tm Net weight 0.126 kg
Recommended frequency range 2500-30000Hz Overall dimension ø62.2x43 mm
* Depending on crossover
First off take notice of the size of these babies... They are massive! (28mm) And very heavy as well.
I quickly knocked up a bracket for them last night (mounted in the kicks again) and wired them up. They extend down very low for tweets - with a fs of 1360 hz.
Also handle all the power I have to give them with great detail and warmth.
I've moved the Morels up to ambients, which was a bit of a struggle getting them to fit in the same holders, but after a bit of modding got them in.
Absolutely love these Dyn's. Cant recommend Dynaudio and Morel more highly.
Still require a lot of tweaking, but for now Im a happy man.
Peace
Tim