Hi, these are some of my bolt-on mods so far. Sorry for the resolution.
http://img.villagephotos.com/p/2005-1/942232/image_00038.jpg
K&N pod Filter and Oil/Air Separator Tank

http://img.villagephotos.com/p/2005-1/942232/image_00042.jpg
Leather Seat cover (Black with red stitch) and Aluminum Shift Knob

http://i122.photobucket.com/albums/o248/MagnaTech07/image_0004-1.jpg
Grill in Matte Black

nice just woundering with a k and n pod u can take the rest of the old air flow tubing off cant you and nice knob always did like the look of shiny metal to set things off

nice just woundering with a k and n pod u can take the rest of the old air flow tubing off cant you and nice knob always did like the look of shiny metal to set things off
The snorkel, to which I assume you refer to as 'air flow tubing' is there for CAI as standard on third gen engines. If you take that off you'll be sucking more hot engine bay air than you already are. Not a clue what you really mean though, tubing should remain the same length and volume for optimum performance, the amount of air allowed to pass through the filter is the only restriction really, the MAF is required for normal engine operation too.

@ MagTech, I love that oil catch can, how much did that set you back, and how easy to install? Looks the biz!

@ MagTech, I love that oil catch can, how much did that set you back, and how easy to install? Looks the biz!

I got the oil catch can from ebay for $39.00 (clearing-up sale)delivered, installation is very easy.
Shift knob $35.00 delivered

The leather seat covers look good, were they off that ebay mob?

iv always wondered, what exactly does the catch can actually do. in this instance is it for the bling or it has a role. also are those the leather seat covers you can get off ebay for like 550.just wondering, is the fit tight, does it look ne good and i notice a few wrinkle. do they disappear with usage. i love the black wif red stitching looks hot

iv always wondered, what exactly does the catch can actually do. in this instance is it for the bling or it has a role. also are those the leather seat covers you can get off ebay for like 550.just wondering, is the fit tight, does it look ne good and i notice a few wrinkle. do they disappear with usage. i love the black wif red stitching looks hot

Nope, seat cover is from the Philippines, I ordered it the last time I got home to visit my parents. It cost me only about $100.00 and I'm sorry it's u.s. made synthetic leather.

Oil catch can-as far as I know the pcv line connected to intake plenum carries oil vapors and oil at times, adding oil to air/fuel mixture reduces the fuel octane level, which means lower combustion power. This is usually use in high performance engine but adding this in an N/A engine I believe will do a lot of benefits. Blink is just an add-on. Please correct me guys if I'm not right.

Speaking of that shift knob, anyone done the same to a second gen? I want bling for a gear knob too :P

Oil catch can-as far as I know the pcv line connected to intake plenum carries oil vapors and oil at times, adding oil to air/fuel mixture reduces the fuel octane level, which means lower combustion power. This is usually use in high performance engine but adding this in an N/A engine I believe will do a lot of benefits. Blink is just an add-on. Please correct me guys if I'm not right.

You're pretty much right on mate.. only thing is that it looks like yours is connected to the breather tube and not the PCV line mate. Not that its a bad thing, but its more beneficial on the PVC. Alot of the 2nd genners run clear $2 fuel filters on the breathers instead, which do a good job! Just replace every service or 2.

same gear knob as me :D ive cut down that little plastic stick inside the shaft so the knob doesnt sit as high... looks a bit dicky when it sits up high

same gear knob as me :D ive cut down that little plastic stick inside the shaft so the knob doesnt sit as high... looks a bit dicky when it sits up high

yeah, i did the same too.

Hi, these are some of my bolt-on mods so far. Sorry for the resolution.
http://img.villagephotos.com/p/2005-1/942232/image_00038.jpg
K&N pod Filter and Oil/Air Separator Tank

http://img.villagephotos.com/p/2005-1/942232/image_00042.jpg
Leather Seat cover (Black with red stitch) and Aluminum Shift Knob

http://i122.photobucket.com/albums/o248/MagnaTech07/image_0004-1.jpg
Grill in Matte Black

I agree with Firestorm - the catch can should be on the PCV line

It won't separate much oil where it is ATM

That grille would look awesome with parras!

I agree with Firestorm - the catch can should be on the PCV line

It won't separate much oil where it is ATM

Ha ha, yeah I know. quick eyes there. No problem I moved it already to where it should be.
http://img.villagephotos.com/p/2005-1/942232/image_00048.jpg

That grille would look awesome with parras!
Yeah but I'm planning a cheap one only,maybe custom made headlight mask.

Yeah but I'm planning a cheap one only,maybe custom made headlight mask.

Awesome... or maybe try black eyelids for something unique. :D