hey guys just wondering how you re set the abs and tcl light after the issue has been fixed cheers

With a muttII

ok and do you know roughly how much it would cost to get cleared and where i would go? cheers

Hey Revhead,
You might be able to reset your ABS yourself.... This is from the manual for your car I think... had a quick look on your profile...

WITHOUT MUT-II
1. Press on the brake pedal so that the brake pedal switch
is on.
2. Switch the ignition ON.
3. Wait until the ABS warning lamp goes out, then release
the brake pedal.
4. “Toggle” the brake pedal so that the ABS–ECU receives
a brake pedal switch on signal 9 times in 20 seconds.
5. The warning lamp will illuminate for 1 second to confirm
code erasure.

Have Fun - Hope it works.
The above came strait from the manual that I downloaded after finding a link on this web site.

hey just wondering if this will work http://www.evoscan.com/evoscan-gps-obdii-cables/details/14/1/performance-vehicle-pc-diagnostic-interfaces/openport-13r-usb-datalogging-and-reflashing-cable and also would it be ok to grab the link off you to down load the manual cheers

Hey Revhead,
You might be able to reset your ABS yourself.... This is from the manual for your car I think... had a quick look on your profile...

WITHOUT MUT-II
1. Press on the brake pedal so that the brake pedal switch
is on.
2. Switch the ignition ON.
3. Wait until the ABS warning lamp goes out, then release
the brake pedal.
4. “Toggle” the brake pedal so that the ABS–ECU receives
a brake pedal switch on signal 9 times in 20 seconds.
5. The warning lamp will illuminate for 1 second to confirm
code erasure.

Have Fun - Hope it works.
The above came strait from the manual that I downloaded after finding a link on this web site.

Where in the workshop manual did you get that from? What section number?

Hi Savage,
I am using a copy of a CD Manual - I think the section number you may be after is 35B.... but if that doesnt help, the file path from the Computer manual is....... TH/KH - Service Brakes - Anti-Lock Braking System (ABS) - Erasing diagnosis codes.

And did this work Revhead?

Hi Savage,
I am using a copy of a CD Manual - I think the section number you may be after is 35B.... but if that doesnt help, the file path from the Computer manual is....... TH/KH - Service Brakes - Anti-Lock Braking System (ABS) - Erasing diagnosis codes.

And did this work Revhead?

nah didnt work for me :( i could be doing it wrong lol. im thinking about getting this but want to make sure it definately will work for my car lol cheers

Ahh I found that. Didn't work though. (Thought you were talking about the SRS) Thanks anyway for following it up.

nah didnt work for me :( i could be doing it wrong lol. im thinking about getting this but want to make sure it definately will work for my car lol cheers

http://www.evoscan.com/evoscan-gps-obdii-cables/details/14/1/performance-vehicle-pc-diagnostic-interfaces/openport-13r-usb-datalogging-and-reflashing-cable

will this work on my th magna for the mutII

Hey Revhead,
You might be able to reset your ABS yourself.... This is from the manual for your car I think... had a quick look on your profile...

WITHOUT MUT-II
1. Press on the brake pedal so that the brake pedal switch
is on.
2. Switch the ignition ON.
3. Wait until the ABS warning lamp goes out, then release
the brake pedal.
4. “Toggle” the brake pedal so that the ABS–ECU receives
a brake pedal switch on signal 9 times in 20 seconds.
5. The warning lamp will illuminate for 1 second to confirm
code erasure.

Have Fun - Hope it works.
The above came strait from the manual that I downloaded after finding a link on this web site.


hey tried this again today and it worked :) thanks for the helpful info